Supported coding options

BMW 6 Series, M6
F06, F12, F13
  • Checkbox acoustical lock confirmation

    Enable/disable the checkbox in the settings for doors/keys in the iDrive system to enable/disable the acoustical lock confirmation. If the checkbox in the iDrive system does not allow selection, please check if “Acoustical lock/unlock confirmation” in the “Roof Function Center” control unit is set to “Active“ also. Please note that the car has to be equipped with an alarm system.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_CIC or “Headunit” HU_NBT control unit
  • Active Cruise Control default distance

    The default distance level of the Active Cruise Control on activation.

    Values:
    • Level 1
    • Level 2
    • Level 3
    • Level 4
    Requirements:
    • “Integrated Chassis Management” ICMQL control unit
  • Active Sound Design deactivation

    Deactivate the Active Sound Design. Use a backup to revert this coding once it has been applied.

    Values:
    • Deactivated
    Requirements:
    • “Active Sound Design” ASD_01 control unit
  • Air circulation setting memory

    Enable/disable storing of the air circulation setting. If this function is active, the last used air circulation setting will be restored during the next start of the car.

    Values:
    • Active
    • Not active
    Requirements:
    • “Air Conditioning” IHKA_CBF control unit
  • Air conditioning on in AUTO mode

    Enable/disable the automatic activation of the air conditioning when the AUTO mode is turned on.

    Values:
    • Active
    • Not active
    Requirements:
    • “Air Conditioning” IHKA_CBF control unit
  • Air conditioning setting memory

    Enable/disable storing of the air conditioning setting. If this function is active, the last used air conditioning setting will be restored during the next start of the car.

    Values:
    • Active
    • Not active
    Requirements:
    • “Air Conditioning” IHKA_CBF control unit
  • Ambient lighting brightness

    The brightness of the ambient lighting.

    Values:
    • 10%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Angel Eyes brightness low beam

    The brightness of the Angel Eyes with low beam.

    Values:
    • 6%
    • 8%
    • 10%
    • 16%
    • 100%
    • 6 V
    • 7 V
    • 7,4 V
    • 11,7 V
    • 13 V
    • 13,7 V
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Bluetooth audio streaming

    This coding enables wireless audio streaming via Bluetooth. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT control unit
  • Bluetooth audio streaming (1 of 2)

    This coding enables wireless audio streaming via Bluetooth. Please note that for this function, “Bluetooth audio streaming (2 of 2)“ must also be activated in the “Combox“ control unit. If there is no “Combox“ installed in your car, Bluetooth audio streaming is not possible unfortunately. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_CIC control unit
  • Bluetooth audio streaming (2 of 2)

    This coding enables wireless audio streaming via Bluetooth. Please note that for this function, “Bluetooth audio streaming (1 of 2)“ must also be activated in the “Headunit“ control unit. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Combox” Combox_Media control unit
  • Maximum volume at start-up

    The maximum volume that is saved when the iDrive system is shut off and restored automatically on the next start-up.

    Values:
    • 10%
    • 20%
    • 25%
    • 30%
    • 40%
    • 50%
    Requirements:
    • “Headunit” HU_CIC or “Headunit” HU_NBT control unit
  • Ringtone

    The ringtone that is used in case of an incoming call.

    Values:
    • Ringtone 1
    • Ringtone 2
    • Ringtone 3
    • Smartphone ringtone
    Requirements:
    • “Combox” Combox_Media control unit
  • Ringtone

    The ringtone that is used in case of an incoming call.

    Values:
    • BMW i ringtone
    • BMW ringtone
    • Mini ringtone
    • Smartphone ringtone
    Requirements:
    • “Headunit” HU_NBT control unit
  • Shut off iDrive system when driver door is opened

    Enable/disable the automatic shut-off of the iDrive system when the driver door is opened.

    Values:
    • Active
    • Not active
    Requirements:
    • “Car Access System” CAS control unit
  • Warning chime

    The warning chime that sounds when a warning is displayed in the car.

    Values:
    • BMW i warning chime
    • BMW warning chime
    • Mini warning chime
    • Rolls Royce warning chime
    Requirements:
    • “Headunit” HU_NBT control unit
  • Auto Start Stop function memory

    Save the last used Auto Start Stop function setting for the next start of the car. Please note that the Auto Start Stop function is automatically activated again in ECO PRO driving mode.

    Values:
    • Active
    • Not active
    Requirements:
    • “Car Access System” CAS control unit
  • Auto Start Stop function off by default

    Set the Auto Start Stop function to off by default when the car is started. Please note that the Auto Start Stop function is automatically activated again in ECO PRO driving mode.

    Values:
    • Active
    • Not active
    Requirements:
    • “Car Access System” CAS control unit
  • Battery type

    The type and capacity of the 12 V battery. Please note that this value must only be modified if the battery in the car has been replaced. After coding, the battery replacement has to be registered using “BimmerLink” additionally.

    Values:
    • 70 Ah
    • 70 Ah AGM
    • 80 Ah
    • 80 Ah AGM
    • 90 Ah
    • 90 Ah AGM
    • 105 Ah AGM
    Requirements:
    • “Car Access System” CAS control unit
  • Blind spot detection activation speed

    The speed at which the blind spot detection system is activated.

    Values:
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 50 km/h
    Requirements:
    • “Integrated Chassis Management” ICMQL control unit
  • Brake Force Display activation brake force

    The brake deceleration at which the Brake Force Display is activated.

    Values:
    • Weak braking (5 m/s²)
    • Medium braking (7 m/s²)
    • Hard braking (8 m/s²)
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Brake Force Display activation speed

    The speed at which the Brake Force Display is activated.

    Values:
    • 5 km/h
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Brake Force Display flashing frequency

    The flashing frequency of the Brake Force Display.

    Values:
    • 3 times per second
    • 5 times per second
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Brake Force Display type

    The type of the Brake Force Display. The Brake Force Display is activated during hard braking to warn the following traffic.

    Values:
    • Area enlargement
    • Flashing
    • Not active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Convenient closing

    Enable/disable the convenient closing. During convenient closing the windows are closed and the power folding mirrors are folded in. To trigger convenient closing the lock button on the remote control has to be pressed and held. Please note that this option does not work for convertibles.

    Values:
    • Active
    • Not active
    Requirements:
    • “Car Access System” CAS control unit
  • Convenient closing delay

    The delay for the convenient closing before the windows are closed.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • No delay
    Requirements:
    • “Car Access System” CAS control unit
  • Convenient closing delay front windows

    The delay at which the front windows are closed during convenient closing.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • No delay
    Requirements:
    • “Car Access System” CAS control unit
  • Convenient closing delay sunroof

    The delay as of with the sunroof is closed during convenient closing.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • 3.5 seconds
    • No delay
    Requirements:
    • “Car Access System” CAS control unit
  • Convenient closing with Comfort Access

    Enable/disable the convenient closing with the Comfort Access. For convenient closing with the Comfort Access the door handle has to be touched and held at the ribbed surface. Please note that this option does not work for convertibles.

    Values:
    • Active
    • Not active
    Requirements:
    • “Car Access System” CAS control unit
  • Convenient closing with remote control

    Enable/disable the convenient closing with the remote control. For convenient closing with the remote control, the lock button has to be pressed and held. Please note that this option does not work for convertibles.

    Values:
    • Active
    • Not active
    Requirements:
    • “Car Access System” CAS control unit
  • Convenient opening

    Enable/disable the convenient opening. During convenient opening the windows are opened and the power folding mirrors are unfolded. For a convenient opening the unlock button on the remote control has to be pressed and held. When using Comfort Access, the door handle has to be gripped and held.

    Values:
    • Active
    • Not active
    Requirements:
    • “Car Access System” CAS control unit
  • Convenient opening delay rear windows

    The delay at which the rear windows are opened during convenient opening.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • No delay
    Requirements:
    • “Car Access System” CAS control unit
  • Convenient opening delay sunroof

    The delay as of with the sunroof is opened during convenient opening.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • 3.5 seconds
    • No delay
    Requirements:
    • “Car Access System” CAS control unit
  • Convenient opening with remote control

    Enable/disable the convenient opening with the remote control. For convenient opening with the remote control, the unlock button has to be pressed and held.

    Values:
    • Active
    • Not active
    Requirements:
    • “Car Access System” CAS control unit
  • Checkbox daytime running light

    Enable/disable the checkbox in the lighting settings in the iDrive system to turn the daytime running light on or off.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_CIC or “Headunit” HU_NBT control unit
  • Daytime running light brightness

    The brightness of the daytime running light.

    Values:
    • 10%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Daytime running light mode

    The mode of the daytime running light.

    Values:
    • Deactivated
    • Norther country comfort
    • Rings and tail lights (ECE Xenon)
    • Rings and tail lights (US Xenon)
    • Rings without tail lights (ECE)
    • Rings without tail lights (US)
    • Via high beam (US halogen, without tail lights)
    • Via low beam
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Display full text messages

    Enable the full display of text messages while driving. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT control unit
  • Pressure and temperature in tyre pressure monitor

    Enable/disable the pressure and temperature in the tyre pressure monitor in the iDrive system. Please note that the car has to be equipped with the required sensors. This option affects the display only and it is not possible to completely deactivate the tire pressure monitoring in the car.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_CIC control unit
  • Rear view camera zoom

    Enable/disable the rear view camera zoom to the trailer hitch.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT control unit
  • Service history

    Enable/disable the service history in the iDrive system.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_CIC or “Headunit” HU_NBT control unit
  • Start animation

    The animation that is displayed when the iDrive system is started. Please note that the animation is not visible every time you start the car, but only under certain circumstances.

    Values:
    • ALPINA
    • BMW 1
    • BMW 2
    • BMW i
    • Christmas
    • Connected Drive 1
    • Connected Drive 2
    • M variant 1
    • MINI variant 1
    • Rolls Royce
    Requirements:
    • “Headunit” HU_NBT control unit
  • Tire pressure control

    The displayed values of the tire pressure control in the iDrive system. Please note that the car has to be equipped with the required sensors to make this work.

    Values:
    • Display pressure only
    • Display temperature and pressure
    • Not active
    Requirements:
    • “Headunit” HU_NBT control unit
  • Volume popup

    Enable/disable the volume popup that is displayed when the volume is changed.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT control unit
  • Additional digital speed in speedometer

    Enable/disabled the additional digital speed display in speedometer.

    Values:
    • km/h
    • mph
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI FPK_I12 control unit
  • Average values reset

    The average speed and consumption is reset after the set time automatically.

    Values:
    • After 4 hours
    • After 8 hours
    • After every ride
    • Never
    Requirements:
    • “Instrument Cluster” KOMBI FPK_I12 or “Instrument Cluster” KOMBI L6 BO control unit
  • Digital speed in board computer

    Enable/disable the display of the digital speed in the board computer. Please toggle the displayed information in the board computer with the button in the turn signal lever until the specific display appears.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI L6 BO control unit
  • Empty menu item in board computer

    Enable/disable the empty menu item in the board computer.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI FPK_I12 or “Instrument Cluster” KOMBI L6 BO control unit
  • M Performance logo

    The model-specific M Performance logo that is displayed in the bottom right in the instrument cluster.

    Values:
    • Not active
    • BMW
    • M Performance
    • BMW i
    • M Performance X5
    • M Performance X6
    Requirements:
    • “Instrument Cluster” KOMBI FPK_I12 control unit
  • Speedometer scale end value

    The end value of the speedometer in the instrument cluster.

    Values:
    • 160_MPH
    • 260_KMH
    • 300_KMH
    • 330_KMH
    Requirements:
    • “Instrument Cluster” KOMBI FPK_I12 control unit
  • “Speed Limit Info” road sign type

    The road sign type of the “Speed Limit Info”. Please note that the car has to be equipped with the “Speed Limit Info” by factory.

    Values:
    • Country-specific
    • Default
    • White Europe
    • White USA
    Requirements:
    • “Camera-based Driver Assistance System” KAFAS control unit
  • Horn signal when locking the car with engine running

    Enable/disable the horn signal that sounds when locking the car with the engine running.

    Values:
    • Active
    • Not active
    Requirements:
    • “Car Access System” CAS control unit
  • Lock after pulling away

    Enable/disable the “Lock after pulling away“ checkbox in the settings in the iDrive system in the car.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT control unit
  • Lock doors automatically

    The doors are locked automatically when reaching the set speed.

    Values:
    • Not active
    • 2 km/h
    • 3 km/h
    • 5 km/h
    • 8 km/h
    • 10 km/h
    • 16 km/h
    • 20 km/h
    • 24 km/h
    • 30 km/h
    • 32 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Car Access System” CAS control unit
  • Unlock doors automatically

    The doors are unlocked automatically when the key is removed. Please note that this only works if the doors have been locked automatically before.

    Values:
    • Active
    • Not active
    Requirements:
    • “Car Access System” CAS control unit
  • Window lifter interruption when opening a door

    Enable/disable the window lifter interruption when a door is opened.

    Values:
    • Active
    • Not active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Road edge warning

    Enable/disable the road edge warning of the lane departure warning.

    Values:
    • Curb stone only
    • Grass and curb stone
    • Grass only
    • Not active
    Requirements:
    • “Camera-based Driver Assistance System” KAFAS control unit
  • Start in ECO mode

    Enable/disable the ECO driving mode as default.

    Values:
    • Active
    • Not active
    Requirements:
    • “Integrated Chassis Management” ICMQL control unit
  • Easy entry protection area

    The protection area limits the rearward travel of the seat when easy entry is activated.

    Values:
    • 0 mm
    • 10 mm
    • 20 mm
    • 30 mm
    • 40 mm
    • 50 mm
    • 60 mm
    • 70 mm
    • 80 mm
    • 90 mm
    • 100 mm
    Requirements:
    • “Seat Module Passenger” CBFS_PLX_1 or “Seat Module Driver” CFAS_PLX_1 control unit
  • Easy entry seat movement

    In order to make it easier to get in the car, the seat is automatically moved back when unlocked and then returns to its original position when the ignition is switched on. Please note that the car has to be equipped with electrically adjustable seats with memory function.

    Values:
    • Active
    Requirements:
    • “Seat Module Passenger” CBFS_PLX_1 or “Seat Module Driver” CFAS_PLX_1 control unit
  • Easy entry seat travel

    The seat travel of the seat when easy entry is activated.

    Values:
    • 10 mm
    • 20 mm
    • 30 mm
    • 40 mm
    • 50 mm
    • 60 mm
    • 70 mm
    • 80 mm
    • 90 mm
    • 100 mm
    Requirements:
    • “Seat Module Passenger” CBFS_PLX_1 or “Seat Module Driver” CFAS_PLX_1 control unit
  • Easy entry steering wheel inclination adjustment

    The steering wheel is moved up/down when easy entry is activated. Please note that the car has to be equipped with an electrically adjustable steering wheel.

    Values:
    • Active
    • Not active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Easy entry steering wheel longitudinal adjustment

    The steering wheel is moved back/forward when easy entry is activated. Please note that the car has to be equipped with an electrically adjustable steering wheel.

    Values:
    • Active
    • Not active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Low fuel warning 1

    The remaining range at which the permanent low fuel warning is displayed.

    Values:
    • 10 kilometers
    • 10 miles
    • 20 kilometers
    • 20 miles
    • 30 kilometers
    • 30 miles
    • 40 kilometers
    • 50 kilometers
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI FPK_I12 or “Instrument Cluster” KOMBI L6 BO control unit
  • Low fuel warning 2

    The remaining range at which the temporary low fuel warning is displayed.

    Values:
    • 40 miles
    • 50 kilometers
    • 50 miles
    • 60 kilometers
    • 70 kilometers
    • 80 kilometers
    • 90 kilometers
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI FPK_I12 or “Instrument Cluster” KOMBI L6 BO control unit
  • HUD music lists

    Enable/disable music lists in the HUD.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI FPK_I12 or “Instrument Cluster” KOMBI L6 BO control unit
  • HUD phone book

    Enable/disable the telephone book in the HUD.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI L6 BO control unit
  • HUD telephone list

    Enable/disable the telephone list in the HUD.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI L6 BO control unit
  • HUD turn signals (1 of 2)

    Enable/disable the turn signals in the HUD. Please note that “HUD turn signals (2 of 2)” in the “Headunit” control unit has to be enabled additionally. This function is not supported, if the car is equipped with a fully digital instrument cluster.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI FPK_I12 or “Instrument Cluster” KOMBI L6 BO control unit
  • HUD turn signals (2 of 2)

    Enable/disable the turn signals in the HUD. Please note that “HUD turn signals (1 of 2)” in the “Instrument Cluster” control unit has to be enabled additionally. It may also be necessary to enable the corresponding checkbox in the HUD settings in the iDrive system in the car. This function is not supported, if the car is equipped with a fully digital instrument cluster.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_CIC or “Headunit” HU_NBT control unit
  • HUD voice input

    Enabled/disable voice input display in the HUD.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI L6 BO control unit
  • Headlight cleaning blocking time

    The blocking time between headlight cleaning activations.

    Values:
    • 3 minutes
    • 5 minutes
    • 10 minutes
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Headlight cleaning pause between injection pulses

    The pause between the injection pulses of the headlight cleaning system.

    Values:
    • 600 ms
    • 800 ms
    • 1000 ms
    • 1200 ms
    • 1400 ms
    • 1600 ms
    • 1800 ms
    • 2000 ms
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Headlight cleaning system deactivation speed threshold

    The deactivation speed threshold at which the headlight cleaning system is deactivated.

    Values:
    • 160 km/h
    • Not active
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Headlight washers

    Activate/deactivate the headlight washers.

    Values:
    • Active
    • Not active
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Number of washing operations for headlight cleaning

    The number of washing operations at which the headlight cleaning is turned on.

    Values:
    • 1 operation
    • 5 operations
    • 10 operations
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Number of water injection pulses during headlight cleaning

    The number of water injection pulses during headlight cleaning.

    Values:
    • 2 times
    • 3 times
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Water injection duration for headlight cleaning

    The duration of the water injection pulses of the headlight cleaning system.

    Values:
    • 600 ms
    • 800 ms
    • 1000 ms
    • 1200 ms
    • 1400 ms
    • 1600 ms
    • 1800 ms
    • 2000 ms
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Wipe cycles after front washing

    The number of wipe cycles after front washing

    Values:
    • 1 time
    • 2 times
    • 3 times
    • 4 times
    • 5 times
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • LED conversion Brake Force Display

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion bi-xenon

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion brake light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion center brake light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion daytime running lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion fog lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion front turn signal

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion high beam

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion inner tail lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion license plate light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion low beam

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion outer tail lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion position lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion rear fog light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion rear turn signals

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion reversing light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • LED conversion side turn signal

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Fog lights off with high beam

    Enable/disable the automatic switch-off of the fog lights when the high beam is turned on.

    Values:
    • Active
    • Not active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Hazard warning signal after emergency braking

    The hazard warning signal is activated automatically after an emergency braking.

    Values:
    • Active
    • Not active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • High beam assistant automatic activation

    Enable/disable the automatic activation of the high beam assistant.

    Values:
    • Automatically
    • Manual
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Rain-light-sensor sensitivity

    The sensitivity of the rain-light-sensor that affects the automatic wiper and light activation.

    Values:
    • Insensitive
    • Normal
    • Sensititve
    • Very sensitive
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Automatic mirror tilt

    Enable/disable the automatic mirror tilt for the right mirror, when the reverse gear is engaged. Please note that your car has to be equipped with power folding mirrors. Make sure the button in the door for selecting the mirror is set to the driver side also.

    Values:
    • Active
    • Not active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Automatic mirror tilt value

    The tilt value of the right mirror, when the reverse gear is engaged.

    Values:
    • 10%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Fold mirrors with convenient closing

    Enable/disable the folding of the mirrors when using convenient closing. Please note that your car has to be equipped with power folding mirrors and that this option does not work for convertibles.

    Values:
    • Active
    • Not active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Fold/unfold mirrors automatically (1 of 2)

    The mirrors are folded automatically when the car is locked with the remote control or Comfort Access and unfolded again when the car is unlocked. Please note that your car has to be equipped with power folding mirrors and that this option does not work for convertibles. “Fold/unfold mirrors automatically (2 of 2)” in the “Footwell Module” control unit has to enabled additionally. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Car Access System” CAS control unit
  • Fold/unfold mirrors automatically (2 of 2)

    The mirrors are folded automatically when the car is locked with the remote control or Comfort Access and unfolded again when the car is unlocked. Please note that your car has to be equipped with power folding mirrors and that this option does not work for convertibles. “Fold/unfold mirrors automatically (1 of 2)” in the “Car Access System” control unit has to enabled additionally. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Mirror folding speed threshold

    The maximum speed at which the mirrors can be folded.

    Values:
    • 5 km/h
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Mirror unfolding speed threshold

    The speed at which the mirrors are unfolded automatically.

    Values:
    • 5 km/h
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Activate PDC when rolling backwards

    Enable/disable the automatic activation of the PDC when the car starts rolling backwards.

    Values:
    • Active
    • Not active
    Requirements:
    • “Park Distance Control” JBBF_E3_PDC or “Park Distance Control” PMA_PDC control unit
  • PDC distance switch-off threshold

    The driven distance after the PDC is turned off automatically.

    Values:
    • 10 m
    • 20 m
    • 30 m
    • 40 m
    • 50 m
    • 100 m
    • 150 m
    • 200 m
    • 250 m
    Requirements:
    • “Park Distance Control” JBBF_E3_PDC control unit
  • PDC distance switch-off threshold
    Values:
    • 10 m
    • 20 m
    • 30 m
    • 40 m
    • 50 m
    • 100 m
    • 150 m
    • 200 m
    • 250 m
    • Not active
    Requirements:
    • “Park Distance Control” PMA_PDC control unit
  • PDC speed switch-off threshold

    The speed at which the PDC is turned off automatically.

    Values:
    • 5 km/h
    • 10 km/h
    • 15 km/h
    • 20 km/h
    • 30 km/h
    • 36 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Park Distance Control” JBBF_E3_PDC or “Park Distance Control” PMA_PDC control unit
  • Rear view camera distance switch-off threshold

    The driven distance after the rear view camera is turned off automatically.

    Values:
    • 10 m
    • 20 m
    • 30 m
    • 40 m
    • 50 m
    • 100 m
    • 150 m
    • 200 m
    • 250 m
    Requirements:
    • “Park Distance Control” JBBF_E3_PDC control unit
  • Rear view camera distance switch-off threshold
    Values:
    • 10 m
    • 20 m
    • 30 m
    • 40 m
    • 50 m
    • 100 m
    • 150 m
    • 200 m
    • 250 m
    • Not active
    Requirements:
    • “Park Distance Control” PMA_PDC control unit
  • Rear view camera speed switch-off threshold

    The speed at which the rear view camera is turned off automatically.

    Values:
    • 5 km/h
    • 10 km/h
    • 15 km/h
    • 20 km/h
    • 30 km/h
    • 36 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Park Distance Control” JBBF_E3_PDC or “Park Distance Control” PMA_PDC control unit
  • HiFi loudspeaker system

    Coding for a retrofitted HiFi loudspeaker system. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT control unit
  • Steering wheel heating

    Enable/disable the heating for a retrofitted steering wheel.

    Values:
    • Active
    • Not active
    Requirements:
    • “Steering Column Control Unit” SZL control unit
  • Steering wheel with paddles

    Enable/disable the paddles for a retrofitted steering wheel.

    Values:
    • Active
    • Not active
    Requirements:
    • “Steering Column Control Unit” SZL control unit
  • Front backrests temperature level 1

    The temperature of the front backrests for seat heating level 1.

    Values:
    • 30 °C
    • 31 °C
    • 32 °C
    • 33 °C
    • 34 °C
    • 35 °C
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Front backrests temperature level 2

    The temperature of the front backrests for seat heating level 2.

    Values:
    • 36 °C
    • 37 °C
    • 38 °C
    • 39 °C
    • 40 °C
    • 41 °C
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Front backrests temperature level 3

    The temperature of the front backrests for seat heating level 3.

    Values:
    • 42 °C
    • 43 °C
    • 44 °C
    • 45 °C
    • 46 °C
    • 47 °C
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Front seats temperature level 1

    The temperature of the front seats for seat heating level 1.

    Values:
    • 30 °C
    • 31 °C
    • 32 °C
    • 33 °C
    • 34 °C
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Front seats temperature level 2

    The temperature of the front seats for seat heating level 2.

    Values:
    • 35 °C
    • 36 °C
    • 37 °C
    • 38 °C
    • 39 °C
    • 40 °C
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Front seats temperature level 3

    The temperature of the front seats for seat heating level 3.

    Values:
    • 41 °C
    • 42 °C
    • 43 °C
    • 44 °C
    • 45 °C
    • 46 °C
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Rear backrests temperature level 1

    The temperature of the rear backrests for seat heating level 1.

    Values:
    • 30 °C
    • 31 °C
    • 32 °C
    • 33 °C
    • 34 °C
    • 35 °C
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Rear backrests temperature level 2

    The temperature of the rear backrests for seat heating level 2.

    Values:
    • 36 °C
    • 37 °C
    • 38 °C
    • 39 °C
    • 40 °C
    • 41 °C
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Rear backrests temperature level 3

    The temperature of the rear backrests for seat heating level 3.

    Values:
    • 42 °C
    • 43 °C
    • 44 °C
    • 45 °C
    • 46 °C
    • 47 °C
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Rear seats temperature level 1

    The temperature of the rear seats for seat heating level 1.

    Values:
    • 30 °C
    • 31 °C
    • 32 °C
    • 33 °C
    • 34 °C
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Rear seats temperature level 2

    The temperature of the rear seats for seat heating level 2.

    Values:
    • 35 °C
    • 36 °C
    • 37 °C
    • 38 °C
    • 39 °C
    • 40 °C
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Rear seats temperature level 3

    The temperature of the rear seats for seat heating level 3.

    Values:
    • 41 °C
    • 42 °C
    • 43 °C
    • 44 °C
    • 45 °C
    • 46 °C
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Seat heating/cooling setting memory

    The memory duration of the seat heating/cooling settings.

    Values:
    • 15 minutes
    • 24 hours
    • Do not save
    • Unlimited
    Requirements:
    • “Seat Module Passenger” CBFS_PLX_1 or “Seat Module Driver” CFAS_PLX_1 control unit
  • Initial seat belt reminder after start

    Activate/deactivate the initial acoustic seat belt reminder after the car is started.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt indicator driver seat

    Activate/deactivate the seat belt indicator in the instrument cluster for the driver seat.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt indicator passenger seat

    Activate/deactivate the seat belt indicator in the instrument cluster for the passenger seat.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt indicator rear seats

    Activate/deactivate the seat belt indicator in the instrument cluster for the rear seats.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt reminder distance

    Driven distance at which th seat belt reminder is activated.

    Values:
    • 50 m
    • 100 m
    • 200 m
    • 500 m
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt reminder driver seat

    Activate/deactivate the acoustic and visual seat belt reminder for the driver seat.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt reminder duration

    Duration at which the seat belt reminder stays active.

    Values:
    • 5 seconds
    • 10 seconds
    • 15 seconds
    • 20 seconds
    • 30 seconds
    • 45 seconds
    • 60 seconds
    • 90 seconds
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt reminder passenger seat

    Activate/deactivate the acoustic and visual seat belt reminder for the passenger seat.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4C control unit
  • Seat belt reminder speed

    Speed at which th seat belt reminder is activated.

    Values:
    • 8 km/h
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4C control unit
  • Activation speed threshold side view camera

    The speed at which the side view camera can be activated.

    Values:
    • 15 km/h
    • No speed limit
    Requirements:
    • “Allround View Camera” iCAM or “Allround View Camera” TRSVC control unit
  • Deactivation speed threshold side view camera

    The speed at which the side view camera is deactivated.

    Values:
    • 15 km/h
    • No speed limit
    Requirements:
    • “Allround View Camera” iCAM or “Allround View Camera” TRSVC control unit
  • Sport displays

    Enable/disable the Sport displays in the iDrive system. Please note that in some cars the engine control unit does not transmit the required values to the headunit and in this case the Sport displays will be displayed but remain functionless.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_CIC or “Headunit” HU_NBT control unit
  • Sport displays color

    The color of the Sport displays in the iDrive system.

    Values:
    • Orange
    • Red
    Requirements:
    • “Headunit” HU_NBT control unit
  • Steering wheel heating memory

    The activation of the steering wheel heating is saved and restored the next time the vehicle is started.

    Values:
    • 15 minutes
    • 24 hours
    • Do not save
    • Unlimited
    Requirements:
    • “Junction Box Passenger” JBBFE or “Steering Column Control Unit” SZL control unit
  • Sport Automatic Transmission

    Enable/disable the Sport Automatic Transmission.

    Values:
    • Active
    • Not active
    Requirements:
    • “Electronic Transmission Control” GKEB23 control unit
  • One-touch turn signal cycles

    The number of cycles of the one-touch turn signal function.

    Values:
    • 1 time
    • 2 times
    • 3 times
    • 4 times
    • 5 times
    • 6 times
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Additional video codecs and formats

    Activate additional video codecs and formats (Ogg, Xvid and VCD). Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT control unit
  • Video in motion

    Activate video in motion. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_CIC or “Headunit” HU_NBT control unit
  • Video via USB

    Enable video playback from USB storage media. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT control unit
  • Welcome Light activation

    The position of the light switch at which the Welcome Light is activated.

    Values:
    • Light switch on auto
    • Light switch on auto or 2
    • Not active
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Welcome Light lighting duration

    The lighting duration of the Welcome Light.

    Values:
    • 5 seconds
    • 10 seconds
    • 15 seconds
    • 20 seconds
    • 30 seconds
    • 45 seconds
    • 60 seconds
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Welcome Lights fog lights

    The fog lights are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on (bulb)
    • Soft on (LED)
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Welcome Lights high beam

    The high beam is turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on (bulb)
    • Soft on (LED)
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Welcome Lights license plate lights

    The license plate lights are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on (bulb)
    • Soft on (LED)
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Welcome Lights low beam

    The low beam is turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on (bulb)
    • Soft on (LED)
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Welcome Lights sidemarkers

    The sidemarkers are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on (bulb)
    • Soft on (LED)
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Welcome Lights tail lights

    The tail lights are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Not active
    • Soft on (bulb)
    • Soft on (LED)
    Requirements:
    • “Footwell Module” FRM__03CT control unit
  • Complete wiper cycle

    Enable/disable the completion of the wiper cycle when the car is turned off.

    Values:
    • Active
    • Not active
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Wipe cycles after rear washing

    The number of wipe cycles after rear washing.

    Values:
    • 1 time
    • 2 times
    • 3 times
    • 4 times
    • 5 times
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
  • Wiper level switch back when stationary

    Enable/disable the automatic switch back of the wiper level when the car becomes stationary.

    Values:
    • Active
    • Not active
    Requirements:
    • “Junction Box Passenger” JBBFE control unit
We use cookies to optimize the website and user-experience. Learn more in our Privacy Policy.