Supported coding options

BMW i3
I01
  • Checkbox acoustic pedestrian protection

    Enable/disable the checkbox in the settings in the iDrive system to turn the acoustic pedestrian protection on or off.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT_EVO control unit
  • Remember acoustic pedestrian protection setting

    Enable/disable the storage of the last used acoustic pedestrian protection setting.

    Values:
    • Active
    • Not active
    Requirements:
    • “Vehicle Sound Generator” VSG01 control unit
  • Acoustical lock/unlock confirmation

    Enable/disable the acoustical confirmation when the car is locked/unlocked.

    Values:
    • Active
    • Not active
    Requirements:
    • “Roof Function Center” FZD__08 control unit
  • Checkbox acoustical lock confirmation

    Enable/disable the checkbox in the settings for doors/keys in the iDrive system to enable/disable the acoustical lock confirmation. If the checkbox in the iDrive system does not allow selection, please check if “Acoustical lock/unlock confirmation” in the “Roof Function Center” control unit is set to “Active“ also. Please note that the car has to be equipped with an alarm system.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Confirmation sound duration

    The duration of the confirmation sound that is played when locking/unlocking the car.

    Values:
    • Short
    • Normal
    • Long
    • Very long
    Requirements:
    • “Roof Function Center” FZD__08 control unit
  • Confirmation sound frequency
    Values:
    • Low
    • Normal
    • High
    Requirements:
    • “Roof Function Center” FZD__08 control unit
  • Confirmation sound volume

    The volume of the confirmation sound that is played when locking/unlocking the car.

    Values:
    • Low
    • Normal
    • High
    • Very high
    Requirements:
    • “Roof Function Center” FZD__08 control unit
  • Active Cruise Control default distance

    The default distance level of the Active Cruise Control on activation.

    Values:
    • Level 1
    • Level 2
    • Level 3
    • Level 4
    Requirements:
    • “Optional Extra System” SAS control unit
  • Air circulation setting memory

    Enable/disable storing of the air circulation setting. If this function is active, the last used air circulation setting will be restored during the next start of the car.

    Values:
    • Active
    • Not active
    Requirements:
    • “Air Conditioning” IHKA_VA02 control unit
  • Air conditioning on in AUTO mode

    Enable/disable the automatic activation of the air conditioning when the AUTO mode is turned on.

    Values:
    • Active
    • Not active
    Requirements:
    • “Air Conditioning” IHKA_VA02 control unit
  • Air conditioning setting memory

    Enable/disable storing of the air conditioning setting. If this function is active, the last used air conditioning setting will be restored during the next start of the car.

    Values:
    • Active
    • Not active
    Requirements:
    • “Air Conditioning” IHKA_VA02 control unit
  • Automatic Air Recirculation

    Enable/disable the Automatic Air Recirculation function.

    Values:
    • Active
    • Not active
    Requirements:
    • “Air Conditioning” IHKA_VA02 control unit
  • Display color change

    Enable/disable the color change of the display from white to orange.

    Values:
    • Active
    • Not active
    Requirements:
    • “Air Conditioning” IHKA_VA02 control unit
  • Alarm sound

    The alarm sound that is played when the alarm is triggered.

    Values:
    • Alarm sound Europe
    • Alarm sound Great Britain
    • Alarm sound USA
    Requirements:
    • “Roof Function Center” FZD__08 control unit
  • Interior motion detection

    Enable/disable the interior motion detection of the alarm system. Please note that this function requires the car to be equipped with an alarm system.

    Values:
    • Active
    • Not active
    Requirements:
    • “Roof Function Center” FZD__08 control unit
  • OBD alarm

    The alarm is triggered when the vehicle is locked and communication via the OBD port is detected. Please note that this function requires the car to be equipped with an alarm system.

    Values:
    • Active
    • Not active
    Requirements:
    • “Roof Function Center” FZD__08 control unit
  • Ambient lighting brightness decoupling from instrument cluster

    Enable/disable the decoupling of the brightness of the ambient lighting from the brightness of the instrument cluster.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Angel Eyes brightness

    The brightness of the Angel Eyes with low beam or parking lights. Use a backup to revert this coding once it has been applied. Please note that this coding has to be carried out for both headlights (left and right) separately.

    Values:
    • 100%
    Requirements:
    • “Front Light Electronics” FLE_02 control unit
  • Angel Eyes brightness low beam

    The brightness of the Angel Eyes with low beam.

    Values:
    • 10%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Angel Eyes brightness parking lights

    The brightness of the Angel Eyes with parking lights.

    Values:
    • 10%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Acoustic signal when reverse gear is engaged

    Enable/disable the acoustic signal that sounds when the reverse gear is engaged.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI_I01_F56 control unit
  • Bluetooth audio streaming

    This coding enables wireless audio streaming via Bluetooth. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT control unit
  • Maximum volume at start-up

    The maximum volume that is saved when the iDrive system is shut off and restored automatically on the next start-up.

    Values:
    • 10%
    • 20%
    • 25%
    • 30%
    • 40%
    • 50%
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Ringtone

    The ringtone that is used in case of an incoming call.

    Values:
    • BMW i ringtone
    • BMW ringtone
    • Mini ringtone
    • Smartphone ringtone
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Shut off iDrive system when driver door is opened

    Enable/disable the automatic shut-off of the iDrive system when the driver door is opened.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Warning chime

    The warning chime that sounds when a warning is displayed in the car.

    Values:
    • BMW i warning chime
    • BMW warning chime
    • Mini warning chime
    • Rolls Royce warning chime
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Battery type

    The type and capacity of the 12 V battery. Please note that this value must only be modified if the battery in the car has been replaced. After coding, the battery replacement has to be registered using “BimmerLink” additionally.

    Values:
    • 20 Ah
    • 40 Ah
    • 40 Ah AGM
    • 46 Ah
    • 55 Ah AGM
    • 60 Ah AGM
    • 60 Ah EFB
    • 70 Ah
    • 70 Ah AGM
    • 70 Ah EFB
    • 80 Ah
    • 80 Ah AGM
    • 80 Ah EFB
    • 90 Ah
    • 90 Ah AGM
    • 105 Ah AGM
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Brake Force Display activation brake force

    The brake deceleration at which the Brake Force Display is activated.

    Values:
    • Weak braking (5 m/s²)
    • Medium braking (7 m/s²)
    • Hard braking (8 m/s²)
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Brake Force Display activation speed

    The speed at which the Brake Force Display is activated.

    Values:
    • 5 km/h
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • CarPlay fullscreen mode

    Show CarPlay in full screen mode. Important: This coding only works with the iDrive software versions “NBTevo_X“ and “NBTevo_Y“. You can easily check for yourself which software version is currently installed in your vehicle. To do this, navigate to the version info in the iDrive system in your vehicle (Navigation > Settings > Position and version > Version information). If you can see “NBTevo_X“ or “NBTevo_Y“ here, then full screen mode will work. If you see “NBTevo_N“, “NBTevo_O“, “NBTevo_P“, “NBTevo_Q“, “NBTevo_R“, “NBTevo_S“, “NBTevo_U“, “NBTEvo_V“ or “NBTEvo_W“ instead, then full screen mode can not be enabled with BimmerCode unfortunately. In this case, an update of the i-level from a BMW service partner is required first.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT_EVO control unit
  • Convenient closing

    Enable/disable the convenient closing. During convenient closing the windows are closed and the power folding mirrors are folded in. To trigger convenient closing the lock button on the remote control has to be pressed and held. Please note that this option does not work for convertibles.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Convenient closing delay

    The delay for the convenient closing before the windows are closed.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • No delay
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Convenient closing delay front windows

    The delay at which the front windows are closed during convenient closing.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • No delay
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Convenient closing delay sunroof

    The delay as of with the sunroof is closed during convenient closing.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • 3.5 seconds
    • No delay
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Convenient closing with Comfort Access

    Enable/disable the convenient closing with the Comfort Access. For convenient closing with the Comfort Access the door handle has to be touched and held at the ribbed surface. Please note that this option does not work for convertibles.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Convenient closing with remote control

    Enable/disable the convenient closing with the remote control. For convenient closing with the remote control, the lock button has to be pressed and held. Please note that this option does not work for convertibles.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Convenient opening

    Enable/disable the convenient opening. During convenient opening the windows are opened and the power folding mirrors are unfolded. For a convenient opening the unlock button on the remote control has to be pressed and held. When using Comfort Access, the door handle has to be gripped and held.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Convenient opening delay

    The delay for the convenient opening before the windows are opened.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • 2 seconds
    • 2.5 seconds
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Convenient opening delay rear windows

    The delay at which the rear windows are opened during convenient opening.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • No delay
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Convenient opening delay sunroof

    The delay as of with the sunroof is opened during convenient opening.

    Values:
    • 0.5 seconds
    • 1 second
    • 1.5 seconds
    • 3.5 seconds
    • No delay
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Convenient opening with remote control

    Enable/disable the convenient opening with the remote control. For convenient opening with the remote control, the unlock button has to be pressed and held.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Checkbox daytime running light

    Enable/disable the checkbox in the lighting settings in the iDrive system to turn the daytime running light on or off.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Daytime running light mode

    The daytime running light mode.

    Values:
    • Active
    • Active also with parking lights
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Daytime running light tail lights inner part
    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Daytime running light tail lights outer part
    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Display full text messages

    Enable the full display of text messages while driving. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Rear view camera zoom

    Enable/disable the rear view camera zoom to the trailer hitch.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT control unit
  • Service history

    Enable/disable the service history in the iDrive system.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Start animation

    The animation that is displayed when the iDrive system is started. Please note that the animation is not visible every time you start the car, but only under certain circumstances.

    Values:
    • ALPINA
    • BMW 1
    • BMW 2
    • BMW i
    • Christmas
    • Connected Drive 1
    • Connected Drive 2
    • M variant 1
    • MINI variant 1
    • Rolls Royce
    Requirements:
    • “Headunit” HU_NBT control unit
  • Start animation

    The animation that is displayed when the iDrive system is started. Please note that the animation is not visible every time you start the car, but only under certain circumstances.

    Values:
    • ALPINA
    • BMW i
    • Connected Drive
    • M variant 1
    • M variant 2
    • MINI John Cooper Works
    • MINI variant 1
    • MINI variant 2
    • Rolls Royce
    Requirements:
    • “Headunit” HU_NBT_EVO control unit
  • Start screen

    The type of start screen that is displayed when the head unit starts up.

    Values:
    • Animation
    • Welcome screen
    Requirements:
    • “Headunit” HU_NBT_EVO control unit
  • Tire pressure control

    The displayed values of the tire pressure control in the iDrive system. Please note that the car has to be equipped with the required sensors to make this work.

    Values:
    • Display pressure only
    • Display temperature and pressure
    • Not active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Volume popup

    Enable/disable the volume popup that is displayed when the volume is changed.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Average values reset

    The average speed and consumption is reset after the set time automatically.

    Values:
    • After 4 hours
    • After 8 hours
    • After every ride
    • Never
    Requirements:
    • “Instrument Cluster” KOMBI_I01_F56 control unit
  • Empty menu item in board computer

    Enable/disable the empty menu item in the board computer.

    Values:
    • Active
    • Not active
    Requirements:
    • “Instrument Cluster” KOMBI_I01_F56 control unit
  • “Speed Limit Info” road sign type

    The road sign type of the “Speed Limit Info”. Please note that the car has to be equipped with the “Speed Limit Info” by factory.

    Values:
    • Country-specific
    • Default
    • White Europe
    • White USA
    Requirements:
    • “Camera-based Driver Assistance System” KAFAS control unit
  • Horn signal when locking the car with engine running

    Enable/disable the horn signal that sounds when locking the car with the engine running.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Lock after pulling away

    Enable/disable the “Lock after pulling away“ checkbox in the settings in the iDrive system in the car.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Time until automatic lock

    The car is locked automatically again if it has been unlocked and no door has been opened within the set time.

    Values:
    • 10 seconds
    • 30 seconds
    • 1 minute
    • 2 minutes
    • 5 minutes
    • 10 minutes
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Unlock doors automatically

    Enable/disable the automatic unlock of the doors when the ignition is turned off.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Window lifter interruption when opening a door

    Enable/disable the window lifter interruption when a door is opened.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Road edge warning

    Enable/disable the road edge warning of the lane departure warning.

    Values:
    • Curb stone only
    • Grass and curb stone
    • Grass only
    • Not active
    Requirements:
    • “Camera-based Driver Assistance System” KAFAS control unit
  • Default driving mode

    The default driving mode on start-up.

    Values:
    • Comfort
    • ECO PRO
    • ECO PRO+
    • Sport
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Driving mode memory

    Enable the driving mode memory. The last used driving mode is stored when the car is turned off and restored on the next start-up. Use a backup to revert this coding once it has been applied.

    Values:
    • 15 minutes
    • Always
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Headlight cleaning blocking time

    The blocking time between headlight cleaning activations.

    Values:
    • 1 minute
    • 2 minutes
    • 3 minutes
    • 4 minutes
    • 5 minutes
    • 6 minutes
    • 7 minutes
    • 8 minutes
    • 9 minutes
    • 10 minutes
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Headlight cleaning pause between injection pulses

    The pause between the injection pulses of the headlight cleaning system.

    Values:
    • 200 ms
    • 400 ms
    • 600 ms
    • 800 ms
    • 1000 ms
    • 1200 ms
    • 1400 ms
    • 1600 ms
    • 1800 ms
    • 2000 ms
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Headlight cleaning system deactivation speed threshold

    The deactivation speed threshold at which the headlight cleaning system is deactivated.

    Values:
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    • 60 km/h
    • 70 km/h
    • 80 km/h
    • 90 km/h
    • 100 km/h
    • 110 km/h
    • 120 km/h
    • 130 km/h
    • 140 km/h
    • 150 km/h
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Headlight washers

    Activate/deactivate the headlight washers.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Number of washing operations for headlight cleaning

    The number of washing operations at which the headlight cleaning is turned on.

    Values:
    • 1 operation
    • 5 operations
    • 10 operations
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Number of water injection pulses during headlight cleaning

    The number of water injection pulses during headlight cleaning.

    Values:
    • 1 time
    • 2 times
    • 3 times
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Water injection duration for headlight cleaning

    The duration of the water injection pulses of the headlight cleaning system.

    Values:
    • 200 ms
    • 400 ms
    • 600 ms
    • 800 ms
    • 1000 ms
    • 1200 ms
    • 1400 ms
    • 1600 ms
    • 1800 ms
    • 2000 ms
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion Brake Force Display

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion bi-xenon

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion brake light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion center brake light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion daytime running lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion fog lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion front turn signal

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion high beam

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion inner tail lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion license plate light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion low beam

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion outer tail lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion position lights

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion rear fog light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion rear turn signals

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion reversing light

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion side turn signal

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • LED conversion sidemarkers

    Activate this function when the lamps for the corresponding lights have been replaced with LEDs in order to prevent errors in the vehicle from being displayed and the LEDs from flickering. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Door handle lights when reverse gear is engaged

    Enable/disable the automatic activation of the lights in the door handles when the reverse gear is engaged.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Fog lights off with high beam

    Enable/disable the automatic switch-off of the fog lights when the high beam is turned on.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Fog lights with parking lights

    Allows the fog lights to be turned on with parking lights.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Hazard warning signal after emergency braking

    The hazard warning signal is activated automatically after an emergency braking.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Rain-light-sensor sensitivity

    The sensitivity of the rain-light-sensor that affects the automatic wiper and light activation.

    Values:
    • Default
    • Insensitive
    • Normal
    • Sensititve
    • Very sensitive
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Automatic mirror tilt

    Enable/disable the automatic mirror tilt for the right mirror, when the reverse gear is engaged. Please note that your car has to be equipped with power folding mirrors. Make sure the button in the door for selecting the mirror is set to the driver side also.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Automatic mirror tilt value

    The tilt value of the right mirror, when the reverse gear is engaged.

    Values:
    • 10%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Fold mirrors with convenient closing

    Enable/disable the folding of the mirrors when using convenient closing. Please note that your car has to be equipped with power folding mirrors and that this option does not work for convertibles.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Fold/unfold mirrors automatically

    The mirrors are folded automatically when the car is locked with the remote control or Comfort Access and unfolded when the car is unlocked. Please note that your car has to be equipped with power folding mirrors and that this option does not work for convertibles. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Mirror folding speed threshold

    The maximum speed at which the mirrors can be folded.

    Values:
    • 5 km/h
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Mirror unfolding speed threshold

    The speed at which the mirrors are unfolded automatically.

    Values:
    • 5 km/h
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Unfold mirrors with convenient opening

    Enable/disable the unfolding of the mirrors when using convenient opening.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Activate PDC when rolling backwards

    Enable/disable the automatic activation of the PDC when the car starts rolling backwards.

    Values:
    • Active
    • Not active
    Requirements:
    • “Park Distance Control” PMA_PDC control unit
  • PDC distance switch-off threshold

    The driven distance after the PDC is turned off automatically.

    Values:
    • 10 m
    • 20 m
    • 30 m
    • 40 m
    • 50 m
    • 100 m
    • 150 m
    • 200 m
    • 250 m
    Requirements:
    • “Park Distance Control” PMA_PDC control unit
  • PDC speed switch-off threshold

    The speed at which the PDC is turned off automatically.

    Values:
    • 5 km/h
    • 10 km/h
    • 15 km/h
    • 20 km/h
    • 30 km/h
    • 36 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Park Distance Control” PMA_PDC control unit
  • PDC speed switch-off threshold

    The speed at which the PDC is turned off automatically.

    Values:
    • 5 km/h
    • 10 km/h
    • 15 km/h
    • 20 km/h
    • 30 km/h
    • 35 km/h
    • 36 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Park Distance Control” PMA_PDC control unit
  • AM radio

    Enable/disable the AM radio function.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Increase electronically limited fuel capacity

    Removes the electronic limitation of the fuel capacity for the REx. Please note that this only works for the US 60 Ah REx version. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Instrument Cluster” KOMBI_I01_F56 control unit
  • Range Extender menu

    Enable/disable the range extender menu that includes the “Hold state of charge” option.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Rear view camera distance switch-off threshold

    The driven distance after the rear view camera is turned off automatically.

    Values:
    • 10 m
    • 20 m
    • 30 m
    • 40 m
    • 50 m
    • 100 m
    • 150 m
    • 200 m
    • 250 m
    Requirements:
    • “Park Distance Control” PMA_PDC control unit
  • Rear view camera speed switch-off threshold

    The speed at which the rear view camera is turned off automatically.

    Values:
    • 5 km/h
    • 10 km/h
    • 15 km/h
    • 20 km/h
    • 30 km/h
    • 36 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Park Distance Control” PMA_PDC control unit
  • Rear view camera speed switch-off threshold

    The speed at which the rear view camera is turned off automatically.

    Values:
    • 5 km/h
    • 10 km/h
    • 13 km/h
    • 15 km/h
    • 20 km/h
    • 30 km/h
    • 36 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Park Distance Control” PMA_PDC control unit
  • HiFi loudspeaker system

    Coding for a retrofitted HiFi loudspeaker system. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT control unit
  • Front backrests temperature level 1

    The temperature of the front backrests for seat heating level 1.

    Values:
    • 30 °C
    • 31 °C
    • 32 °C
    • 33 °C
    • 34 °C
    • 35 °C
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Front backrests temperature level 2

    The temperature of the front backrests for seat heating level 2.

    Values:
    • 36 °C
    • 37 °C
    • 38 °C
    • 39 °C
    • 40 °C
    • 41 °C
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Front backrests temperature level 3

    The temperature of the front backrests for seat heating level 3.

    Values:
    • 42 °C
    • 43 °C
    • 44 °C
    • 45 °C
    • 46 °C
    • 47 °C
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Front seats temperature level 1

    The temperature of the front seats for seat heating level 1.

    Values:
    • 30 °C
    • 31 °C
    • 32 °C
    • 33 °C
    • 34 °C
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Front seats temperature level 2

    The temperature of the front seats for seat heating level 2.

    Values:
    • 35 °C
    • 36 °C
    • 37 °C
    • 38 °C
    • 39 °C
    • 40 °C
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Front seats temperature level 3

    The temperature of the front seats for seat heating level 3.

    Values:
    • 41 °C
    • 42 °C
    • 43 °C
    • 44 °C
    • 45 °C
    • 46 °C
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Rear backrests temperature level 1

    The temperature of the rear backrests for seat heating level 1.

    Values:
    • 30 °C
    • 31 °C
    • 32 °C
    • 33 °C
    • 34 °C
    • 35 °C
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Rear backrests temperature level 2

    The temperature of the rear backrests for seat heating level 2.

    Values:
    • 36 °C
    • 37 °C
    • 38 °C
    • 39 °C
    • 40 °C
    • 41 °C
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Rear backrests temperature level 3

    The temperature of the rear backrests for seat heating level 3.

    Values:
    • 42 °C
    • 43 °C
    • 44 °C
    • 45 °C
    • 46 °C
    • 47 °C
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Rear seats temperature level 1

    The temperature of the rear seats for seat heating level 1.

    Values:
    • 30 °C
    • 31 °C
    • 32 °C
    • 33 °C
    • 34 °C
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Rear seats temperature level 2

    The temperature of the rear seats for seat heating level 2.

    Values:
    • 35 °C
    • 36 °C
    • 37 °C
    • 38 °C
    • 39 °C
    • 40 °C
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Rear seats temperature level 3

    The temperature of the rear seats for seat heating level 3.

    Values:
    • 41 °C
    • 42 °C
    • 43 °C
    • 44 °C
    • 45 °C
    • 46 °C
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Initial seat belt reminder after start

    Activate/deactivate the initial acoustic seat belt reminder after the car is started.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4i control unit
  • Seat belt indicator driver seat

    Activate/deactivate the seat belt indicator in the instrument cluster for the driver seat.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4i control unit
  • Seat belt indicator passenger seat

    Activate/deactivate the seat belt indicator in the instrument cluster for the passenger seat.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4i control unit
  • Seat belt reminder distance

    Driven distance at which th seat belt reminder is activated.

    Values:
    • 50 m
    • 100 m
    • 200 m
    • 500 m
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4i control unit
  • Seat belt reminder driver seat

    Activate/deactivate the acoustic and visual seat belt reminder for the driver seat.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4i control unit
  • Seat belt reminder duration

    Duration at which the seat belt reminder stays active.

    Values:
    • 5 seconds
    • 10 seconds
    • 15 seconds
    • 20 seconds
    • 30 seconds
    • 45 seconds
    • 60 seconds
    • 90 seconds
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4i control unit
  • Seat belt reminder passenger seat

    Activate/deactivate the acoustic and visual seat belt reminder for the passenger seat.

    Values:
    • Active
    • Not active
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4i control unit
  • Seat belt reminder speed

    Speed at which th seat belt reminder is activated.

    Values:
    • 8 km/h
    • 10 km/h
    • 20 km/h
    • 30 km/h
    • 40 km/h
    • 50 km/h
    Requirements:
    • “Advanced Crash Safety Module” ACSM_4i control unit
  • Activation speed threshold side view camera

    The speed at which the side view camera can be activated.

    Values:
    • 15 km/h
    • No speed limit
    Requirements:
    • “Allround View Camera” iCAM control unit
  • Deactivation speed threshold side view camera

    The speed at which the side view camera is deactivated.

    Values:
    • 15 km/h
    • No speed limit
    Requirements:
    • “Allround View Camera” iCAM control unit
  • Steering wheel heating memory

    The activation of the steering wheel heating is saved and restored the next time the vehicle is started.

    Values:
    • 15 minutes
    • 24 hours
    • Do not save
    • Unlimited
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Boot lid opening delay

    The delay when opening the boot lid with the remote control. This value can be increased to prevent accidental openings of the boot lid.

    Values:
    • 0.5 seconds
    • 0.7 seconds
    • 1 second
    • 5 seconds
    • 10 seconds
    • No delay
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Open tailgate after unlock only

    The tailgate can only be opened after unlocking the car with the remote control. Please note that “Tailgate“ has to be selected for the tailgate button in the settings in the iDrive system in the car.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Turn signals flashing on locking

    Number of turn signal flashes when locking the car.

    Values:
    • 1 time
    • 2 times
    • 3 times
    • Off
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Turn signals flashing on unlocking

    Number of turn signal flashes when unlocking the car.

    Values:
    • 1 time
    • 2 times
    • 3 times
    • Off
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Additional video codecs and formats

    Activate additional video codecs and formats (Ogg, Xvid and VCD). Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Video in motion

    Activate video in motion. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT control unit
  • Video in motion

    Enable video in motion. Please note the instructions displayed after coding.

    Values:
    • Active
    • Not active
    Requirements:
    • “Headunit” HU_NBT_EVO control unit
  • Video via USB

    Enable video playback from USB storage media. Use a backup to revert this coding once it has been applied.

    Values:
    • Active
    Requirements:
    • “Headunit” HU_NBT or “Headunit” HU_NBT_EVO control unit
  • Welcome Light activation

    The position of the light switch at which the Welcome Light is activated.

    Values:
    • Light switch on auto
    • Light switch on auto or 2
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Light in darkness only

    Enable/disable the activation of the Welcome light in darkness only.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Light lighting duration

    The lighting duration of the Welcome Light.

    Values:
    • 5 seconds
    • 10 seconds
    • 15 seconds
    • 20 seconds
    • 30 seconds
    • 45 seconds
    • 60 seconds
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights brake lights

    The brake lights are turned on with the Welcome Lights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights brightness

    The brightness of the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • 10%
    • 20%
    • 30%
    • 40%
    • 50%
    • 60%
    • 70%
    • 80%
    • 90%
    • 100%
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights central turn signals

    The central turn signals are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights daytime running light

    The daytime running light is turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights design lights

    The design lights are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights fog lights

    The fog lights are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights front turn signals

    The front turn signals are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights high beam

    The high beam is turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights inner rear parking lights

    The inner rear parking lights are turned on with the Welcome Lights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights license plate lights

    The license plate lights are turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights low beam

    The low beam is turned on with the Welcome Lights. Please note that this option only works for cars equipped with halogen or xenon headlights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights outer rear parking lights

    The outer rear parking lights are turned on with the Welcome Lights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights parking lights front

    The front parking lights are turned on with the Welcome Lights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights rear fog light left

    The left rear fog light is turned on with the Welcome Lights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights rear fog light right

    The right rear fog light is turned on with the Welcome Lights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights reversing light left

    The left reversing light is turned on with the Welcome Lights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights reversing light right

    The right reversing light is turned on with the Welcome Lights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights third brake light.

    The third brake light is turned on with the Welcome Lights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Welcome Lights turn signals front

    The front turn signals are turned on with the Welcome Lights.

    Values:
    • Hard on
    • Off
    • Soft on
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Complete wiper cycle

    Enable/disable the completion of the wiper cycle when the car is turned off.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Wipe cycles after front washing

    The number of wipe cycles after front washing

    Values:
    • 1 time
    • 2 times
    • 3 times
    • 4 times
    • 5 times
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Wipe cycles after rear washing

    The number of wipe cycles after rear washing.

    Values:
    • 1 time
    • 2 times
    • 3 times
    • 4 times
    • 5 times
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
  • Wiper level switch back when stationary

    Enable/disable the automatic switch back of the wiper level when the car becomes stationary.

    Values:
    • Active
    • Not active
    Requirements:
    • “Body Domain Controller” BDC_BODY control unit
We use cookies to optimize the website and user-experience. Learn more in our Privacy Policy.